Hi there,

Just to share my knowledge. As far as I know, Siemens from the early basic stage (learning process) is tough. S7-300 contain a LADDER,FBD and ?? ( forgot). The advantahe is, during I stuck on design in Ladder, I could switch to FBD ( Funct Logic Block ). This could help me in solving.
During my study in German Malaysia Institute, PLC SIEMENS S7-300 and SIEMENS S7-400 need to do "hand-on". Should I say, "practice make perfect". Once you had succes in making simulation and appply to motor, you will understand and appreciate SIEMENS. Hence, a booklet for PLC SIEMENS is arrange to make reader to understand how to apply.

After graduate, I'm working with Honeywell, and approach to AB.

I assume AB is quit easy during starting design, but after compile, you need to finish by "error and try". I believe, without training at first time, Its hard for me.

we would like to establish a SCADA system for our own trainning using AB..how can we establish the system with a minimum I/O's using the latest model of the PLC?the system most preferably has an analog and digital inputs...
you can also e mail at my email address...
thank you very much

Jan Michael
[email protected]

dear sir,
i m an engineer in a process industry..please help me out .. how to set up real time clock in microLogix 1000(allen bradley) and for omron (cpm1A) is it possible by Cpm1A...please reply as soon as u can sir ... i need the solution immediately...

iam trying to setup the contol logix to get info from the fx2n.i ran devicenet and can see the fx2n.i setup the eds for 64bytes but get an error 77.do you have an eds file for this device.you can mail me...

is there a tutorial for this studio? i need to learn how to use this.. i tried to google it, but only manual of RSlogix.. can anyone help me? thanx in advance

hi;
please give me the address or phone number of delta agency in dubai
thanks.

does anyone have a copy of the circuit diagram for the
1398-ddm-019 driver from allen bradley
if do plz email it to me on
[email protected]

I am a mech eng tech major working on a PLC project. I using a stepper motor to control a table and need it to rotate either 90 or 180 degrees in both directions. How do I control the motor with the PLC using RSLogic? I have seen C++ programs but I don't know how to interface C++ with the PLC. Any help would be apreciated.

I have rslogix500 version 6.10 rs linx ver 2.4 I am tryin to talk to micrologix 1000 from plc win xp tried configuring a driver and now have three running trying to delete two I added or even stop them but gives me blue screen of death besides not even knowing if I have right cable but also dont know what driver to configure.How can I get rid of other two drivers which say error and are running and get back to the beginning .The one driver running is ok for ethernet but want to hook up seperately to different plc .Can anyone help my it guy is gone so now Iam on my own.

does anyone know how to link up an ab plc to a zigbee wireless network system

has anyone loaded RS logix on a vista system what did you have to do to get it to work

iyi günler i?yerimizde sizin plc niz kullan?lmakta bana kendimi geli?tirebilece?im simülatör program? gönderiirmisiniz. veya türkçe kullanma kulavuzu.

How would i go about writing logic to reset a fault condition. Lets say i tripped a limit switch and in turn it closed an input and turned on a fault light. I need to somehow reset that condition with a push button that will turn the fault off. Any help would be appreciated, thank you.

AB pls can be easlity learnt by referring to AB PLC software for example RSlogix 500 or RS logix 5000 help topics , one by one daily one instruction if we learnt , we make our selves a better programmers ,..... the thing is once you hv learnt you hv to make your mind that i know to confidently what i have learnt ..

I know little bit of programming using ladder logic.i want to know about programming using FB. anyone please guide me & also i need training manuals. please send it to my mail.

My mail [email protected]

I don't know anything about PLC. Please how & where would you advise me to start. I use relays a lot but can b very cumbersome.
Ayeminimowa John
[email protected]

I have a site with SLC505. The analog card is working but the ladder program is not sensing any analog inputs. It will be helpful if any one can share some light on what problem might be happening here. This is an emergency and early reposne is appreciated.

Hi friends
I am currently working in AB plc for Larox filters. I have sufficient knowledge to work in Ab plc But i want to knw more abt AB plc.pls help me to find books.

I need a help.
How I can change the configuration of the mod bus card cp441-2 in order to make it communicate with 4-wire rs485

Thanks

Gigs

sir
we have one chocolate moulding machine carle montanari
model 275\175 serial no.550240 v220 phase3 so now problem is
allen bradly panel view model 2711 kc1 colour 1200 keypad
terminal so now is deffected i have old one but now we faicing
probelm is the screen software and the machine program not packup cd so how can sir pls
pLc 1785 L30 BpLc 5/30
thanking you issaki saudi arabia in riyadh

plz i wont learn plc where how can u help me?

Hi all I'm new here and a struggling mature student in second year electrical engineering trying to learn the basics of plc's and actually have passed my first course in plc's . I am hoping there is a free version of the tutorial that's included with the AB RSLogix pro 5000 software so I can get a heads up on learning for next years class?
Thanks
Ron